Raise Rib 4809 plastic straight run conveyor belt

modular straight running belts for Type Spray Sterilization

Raise Rib Top straight running conveyor belt manufacturers

modular plastic straight belting Power transmission equipment

Sprockets for 4809

Sprockets data

Our company has been qualified with ISO 9001:2000 quality system. Theproduction strictly complies with the standard and procedures of ISO 9001, which 

ensures good product quality.

If you are interested in ourproducts, please feel free to contact us.

Modular belts are constructed with modules molded from thermoplastic materials connected with soild plastic rods. Except for narrow belts (one complete module or less in width),all are built with the joints between modules staggered with those of adjacent rows in a

 "bricklayed" fashion. This structure can enhance transverse strength and it is easy for maintain.
The total plastic and cleanable design can solve the steel belts easily polluted.Now the cleanable design makes the belts very suitable for food industry 

area as well.Also there are be widely used in many other industries,such as container making,pharmaceutical and automotive,lines of battery and so on.
Rellwin company has a widely range of different material and structure belts. The range of Rellwin's modular belts varies from 3/8 inch small pitch 

straight running belts to 2inch pitch sideflexing belts,The most commonly used belt styles inclued:
Flat Top:suitable for a wide range of products,when a fully closed belt surface is preferred.
Flush Grid:commonly used in applications where drainage or airflow is desired.
Raised Rib:recommended in applications where product stability over transfers is a concern.
Friction Top:commonly employed on incline conveyors, where the elevation of product changes.Friction Top modular belts can be used up to an angle of 20 degrees,depending on the pack style and material.
Roller Top:used in a variety of low-pressure accumulation applications.
Perforated Flat Top:used when air flow and water flow are critical but the percentage of belt open area must remain low.
Other,less frequently used belt styles may better fit your special requirements:Open Grid,Nub Top(anti-stick),Cone Top(extra grip).

Transportation and daily maintenance of plastic chain plate and belt

1.During storage, the product must be placed into a roll not folded, turning once during placement should be on a quarterly basis

2.Different type, size layers together using the belt should

3.Type conveyor belt, structure, size, number of layers should be a reasonable choice according to the conditions

4.Feed direction along the direction of the tape should be, in order to reduce the impact on the whereabouts of the tape should be taken when the material chute, reducing materials falling distance

Conveyor belts in use should note the following

1.Avoid roller is covered with material, resulting in ineffective rotation to prevent leakage of material between the roller and the tape card, pay attention to the lubrication of moving parts,

2.Avoid starting with a over load

In the past the beverage bottling industry was very noisy due to the use of metallic chains working at high speed. Nowadays the plastic modular belt 

system reduces the noise rate at very acceptable levels.

The use of metallic chains also entailed a high cost in mechanical maintenance, as well as a great consumption of lubricants for decreasing the friction 

coefficient in order to avoid their premature wear. The maintenance cost of the plastic materials used for manufacturing the Rellwin modular belts is the 

lowest, as they do not need any lubrication, which avoids not only the lubricant expenditure, but also the rejection of bottles due to their impregnation with 

those liquids.

Our services

1. Warranty time: 1 year.  The conveyor belt / chains / sprockets which supplied by our company could be exchanged when it have quality problems,such as it was broken in installing , the pin run out from chains or the chains parted . But if the user use it in a wrong way, we can not provide any goods for free .

2. Payment: T/T , L/C , Western Union or Paypal .

3. Lead time: 5~15 working days, subject to the order quantity.

4. Shipment: by sea, by air,door to door service for samples transportation.

5. OEM service : we have our own R.D team . If you want to purchase the belt which we have not or you have your own design , we would like to make mold for you for free , only have the condition of requiring continuous orders ,and first order must be more than 60 square meters .

Company and Productsinformationrelated:
Ningbo Rellwin IndustryCo.,ltd.